Ventilated facades

Applications :
To form floating and fixed points on substructures of rear ventilated facades Fastening pre-drilled stainless steel or aluminium wall brackets to aluminium support profiles For component assemblies from 3.1–5.0 mm (component I + component II)        

Properties :
Drilling capacity: 2.0 mm Drive: hexagon A/F 8 Flange head: Ø 13 mm Material: A2 stainless steel Length non-threaded part: 5.0 mm        

Technical specifications :
Drilling capacity: 2.0 mm Drive: Hexagon AF8 Flange head: Ø 13 mm Material: A2 stainless steel Length non-threaded part: 5.0 mm        

More information on : www.ejot.de

Applications :
Fastening facade panels to aluminium substructure ≤ 3 mm        

Properties :
A2 stainless steel Countersunk head with flange        

Technical specifications :
Drilling capacity tI + tII: 3.0 mm Drive: Hexalobular TORX® T25        

More information on : www.ejot.de

Applications :
For fixing insulating material in the rear ventilated facade (VHF). Advantages Prevents "quilt effect" (indentations in the insulation) with retrofitting of the washer Prevents gaping of the joints between the individual insulation panels at the joining edges Packing and handling volume is reduced by over 60% compared to one-part insulation support anchors Installation depth limiter guarantees defined installation independent of the substrate Equal installation depth for masonry and concrete prevents wrong orders. High-quality plastic material guarantees process reliable installation even with thick insulation For efficient and flexible storage

Properties :
Order descriptions correspond to the High-grade plastic material easy installation with no additional expansion element All-purpose for all building materials flexible stress plate Reduced "quilt effect", due to defined installation depth Minimal packing volume Minimal effort needed to drive in the anchor

Technical specifications :
Drill bit diameter: 8 mm Drill hole depth ≥ t: 40 mm Embedment depth ≥ hv: 30 mm Disc washer diameter: 90 mm Thermal conductivity coefficient: 0.0001 W/K Carrying capacity (pull over washer): 0.2 kN

More information on : www.ejot.de

Applications :
To compensate for tolerances on wall and roof

Properties :
Simple clicking on the anchor between the wall and rail Tolerances can be individually compensated through combination with multiple compensation pieces Sorted by colour

Technical specifications :
Dimensions: 50 x 50 mm

More information on : www.ejot.de

Applications :
Installation of metal components Plastic anchor for multiple use in concrete and masonry for non structural applications Suitable for the structural fastening of cladding and metal angle pieces For installation in rain screen Notes Please note the European Technical Approval ETA-10/0305 in your planning and in the processing of the products. Further information about parameters and loads can be found in the approval.        

Properties :
approved for all common building materials reliable installation in problematic building material due to optimised expansion part secure hold due to radial expansion Cr VI-free coating of the screw Product identification through different sleeve colours double safety lock against torsion for secure installation Installation substrate Approved for: Concrete Solid brick Solid lime sand brick Solid lightweight concrete brick Vertically perforated brick Lightweight vertically perforated brick Perforated lime sand brick Lightweight concrete cavity blocks Porous lightweight concrete Suitable for: natural stone Plaster board non-classified cavity and perforated brick        

Technical specifications :
CHARACTERISTIC VALUES drill hole depth h1 ≥ 80 mm effective embedment depth hnom ≥ 70 mm Drill-hole diameter d0 ≥10 mm Hole diameter of construction part to be installed df ≤ 10.5 mm Drive: hexagon A/F13 + hexalobular / TORX® T40 Characteristic values Tensile load NRk,p in concrete C12/15 Temperature range 30 °C / 50 °C: 4,50 kN Temperature range 50 °C / 80 °C: 4,00 kN Brick Mz 20-1.8, NF: 4.00 kN Solid lime sand brick KS 36, NF: 4.50 kN Solid lime sand brick KS 20, 8 DF: 4.50 kN Solid lightweight concrete brick V6, 2 DF: 2.00 kN Porous lightweight concrete: 2.00 kN Vertically perforated brick HLz 12-0.9, NF: 2.00 kN Perforated lime sand brick KSL 12, 4 DF: 2.50 kN Cavity block tile made of lightweight concrete Hbl 10, 12 DF 1.20 kN Transverse load VRk,s Anchor with steel screw: 9.35 kN Anchor with stainless steel screw A4: 10.91 kN Bending moment MRk,s Anchor with steel screw: 17.67 Nm Anchor with stainless steel screw A4: 20.62 Nm Permitted load* Tensile load Nper in concrete C12/15 Temperature range 30 °C / 50 °C: 1.79 kN Temperature range 50 °C / 80 °C: 1.59 kN Brick Mz 20-1.8, NF: 1.14 kN Solid lime sand brick KS 36, NF: 1.29 kN Solid lime sand brick KS 20, 8 DF: 1.29 kN Solid lightweight concrete brick V6, 2 DF: 0.57 kN Porous lightweight concrete: 0.57 kN Vertically perforated brick HLz 12-0.9, NF: 0.57 kN Perforated lime sand brick KSL 12, 4 DF: 0.71 kN Cavity block tile made of lightweight concrete Hbl 10, 12 DF: 0.34 kN Transverse load Vzul Anchor with steel screw: 5.34 kN Anchor with stainless steel screw A4: 5.00 kN Max. permitted side load Anchor with steel screw: 10.10 Nm Anchor with stainless steel screw A4: 9.44 Nm        

More information on : www.ejot.de

Applications :
For fastening hard insulating materials in combination with the EJOT® DMT metal insulation stress plate and also for soft insulating materials. Fixing insulating materials for high fire protection requirements (cellar ceiling insulation, insulation close to escape routes) Note The EJOT® insulation support anchors are used to fasten soft and hard insulating material in rear ventilated facades. For soft insulation, such as rock or mineral wool, it needs to be considered that the plate diameter is at least 80 mm. The insulation board fastening is carried-out according to DIN 18516-1.        

Properties :
easy installation by striking in, self-expanding no pre-drilling required for aerated concrete easy installation        

Technical specifications :
Drill bit diameter: 8 mm Drill hole depth ≥ t: 60 mm Embedment depth hv: 40 mm Disc washer diameter: 35 mm        

More information on : www.ejot.de

Applications :
For fastening soft insulating materials in combination with the EJOT® DMH metal insulation support anchor Fixing soft insulating materials for high fire protection requirements        

Properties :
"V" - Aluzinc coated carbon steel "E" - A2 stainless steel        

Technical specifications :
80mm ø        

More information on : www.ejot.de

Applications :
Fastening profiled steel and aluminium sheet and sandwich panels 4–10 mm steel substructure Fastening profiled aluminium sheet and sandwich panels 4–12 mm aluminium substructre        

Properties :
A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer        

Technical specifications :
Drilling capacity tI + tII: 1.0 + 12.0 mm / 2.0 + 10.0 mm Drive: Hexagon AF8 Ø screw: 5.5 mm        

More information on : www.ejot.de

Applications :
Installation of metal components Plastic anchors for multiple use in concrete and masonry for non-structural applications Suitable for the structural fastening of wall cupboards, cladding, metal angle pieces Note Please note the European Technical Approval ETA-10/0305 in your planning and in the processing of the products. Further information about parameters and loads can be found in the approval.        

Properties :
Anchor with an embedment depth of 40 mm in concrete Two installation depths (embedment in masonry 50 mm) Very short expansion part, for short installation times Optimal expanding part due to radial expansion Very high bending moment Cr VI-free coating of the screw Product identification through different sleeve colours double safety lock against torsion for secure installation        

Technical specifications :
Characteristic values Hole depth in concrete h1.1: ≥ 50 mm Effective embedment depth in concrete hnom,1: ≥ 40 mm Hole depth in masonry h1.2: ≥ 60 mm Effective embedment depth in masonry hnom,2: ≥ 50 mm Drill-hole diameter d0: 10 mm Hole diameter of construction part to be installed df:Ø 10.5 mm Drive: hexalobular / TORX® T40 Characteristic loads Tensile load NRk,p in concrete C12/15 Temperature range 30 °C / 50 °C: 4.50 kN Temperature range 50 °C / 80 °C: 4.00 kN FRk Brick Mz 20-1.8, NF: 2.50 kN FRk Solid lime sand brick KS 36, NF: 4.00 kN FRk Solid lime sand brick KS 20, 8 DF: 4.50 kN Transverse load VRk,s in concrete C12/15 at hnom,1 = 40 mm Anchor with steel screw: 7.93 kN Anchor with stainless steel screw A4: 9.12 kN Transverse load VRk,s at hnom,2 = 50 mm Anchor with steel screw: 11.09 kN Anchor with stainless steel screw A4: 12.94 kN Bending moment MRk,s at hnom,1 =40 mm Anchor with steel screw: 13.80 Nm Anchor with stainless steel screw A4: 16.09 Nm Side load MRk,s at hnom,2 = 50 mm        

More information on : www.ejot.de

Applications :
Fastening sandwich panels to 1.5–5 mm steel substructures        

Properties :
A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer With free spin zone under the screw head High thread        

Technical specifications :
Drive: Hexagon AF8 Ø screw: 5.5 mm Ø high thread: 6.3 mm        

More information on : www.ejot.de

Applications :
For fixing insulating material in the rear ventilated facade Advantages Prevents "quilt effect" (indentations in the insulation) with retrofitting of the washer Prevents gaping of the joints between the individual insulation panels at the joining edges Packing and handling volume is reduced by over 60% compared to one-part insulation support anchors Installation depth limiter guarantees defined installation independent of the substrate Equal installation depth for masonry and concrete prevents wrong orders. High-quality plastic material guarantees process reliable installation even with thick insulation For efficient and flexible storage  

Properties :
Order descriptions correspond to the High-grade plastic material easy installation with no additional expansion element All-purpose for all building materials flexible stress plate Reduced "quilt effect", due to defined installation depth Minimal packing volume Minimal effort needed to drive in the anchor

Technical specifications :
Drill bit diameter: 8 mm Drill hole depth ≥ t: 40 mm Embedment depth ≥ hv: 30 mm Disc washer diameter: 90 mm Thermal conductivity coefficient: 0.0001 W/K Carrying capacity (pull over washer): 0.2 kN

More information on : www.ejot.de

Applications :
For fixing insulating material in the rear ventilated facade (VHF). Note The EJOT® insulation support anchors are used to fasten soft and hard insulating material in rear ventilated facades. For soft insulation, such as rock or mineral wool, it needs to be considered that the plate diameter is at least 80 mm. The insulation board fastening is carried-out according to DIN 18516-1.        

Properties :
High-grade plastic material easy installation with no additional expansion element All-purpose for all building materials flexible stress plate reduces "quilt effect"        

Technical specifications :
Characteristic values Drill bit diameter: 8 mm Drill hole depth ≥ t: 40 mm embedment depth ≥ hv: 20 mm masonry embedment depth = hv: 40 mm Disc washer diameter: 90 mm        

More information on : www.ejot.de

Applications :
Used in conjunction with the SW8R and TKR to retain insulation to cement particle boards, timber and SFS upto 1.2mm thick

Properties :
Hole diameter: 5.2 mm Washer diameter: 65 mm Isolated washer with an integral cap

More information on : www.ejot.de

Applications :
Ceiling insulation anchor For fastening of ceiling and acoustic insulation Recommended substrate: Concrete  

Properties :
Easy installation: drill, hammer, done! Available in colours beige or white

Technical specifications :
Head diameter: 25 mm Drill hole Diameter: 8 mm Drill hole depth h1 &ge:; 35 mm Embedment depth hef &ge:; 25 mm Recommended substrate: Concrete

More information on : www.ejot.de

Applications :
For fixing metal profiles to timber substructure For fixing metal profiles to aluminium substructure ≤ 2mm        

Properties :
Fully A2 Austenitic Stainless Steel Available unwashered        

Technical specifications :
Drive: hexalobular / TORX® T20        

More information on : www.ejot.de

Applications :
Fastening corrugated profile aluminium sheet to timber substructure        

Properties :
A2 stainless steel with hardened drill point Stainless steel sealing washer Pre-assembled sealing washer Thread according to DIN 7998        

Technical specifications :
Drilling capacity tI + tII: 2.0 mm Drive: Hexalobular TORX® T25        

More information on : www.ejot.de

Applications :
To form floating and fixed points on substructures of rear ventilated facades Fastening pre-drilled stainless steel or aluminium wall brackets to aluminium support profiles For component assemblies from 6.0–7.0 mm (component I + component II)        

Technical specifications :
Drilling capacity: 2.0 mm Drive: hexagon A/F 8 Flange head: Ø 13 mm Material: A2 stainless steel Length non-threaded part: 7.0 mm        

More information on : www.ejot.de

Applications :
Fastening aluminium profiles to aluminium substructure ≤4 mm        

Properties :
A2 stainless steel        

Technical specifications :
Drilling capacity tI + tII: 2.0 + 4.0 mm Drive: Hexagon AF8        

More information on : www.ejot.de

Applications :
Fastening aluminium corrugated profile sheet to aluminium substructure ≤ 3 mm Fastening facade panels to aluminium substructure        

Properties :
A2 stainless steel        

Technical specifications :
Drilling capacity tI + tII: 1.0 + 3.0 mm Drive: Hexalobular TORX® T25        

More information on : www.ejot.de

Applications :
Fastening aluminium corrugated profile sheet to aluminium substructure ≤ 3 mm Fastening facade panels to aluminium substructure        

Properties :
A2 stainless steel        

Technical specifications :
Drill capacity tI + tII: 1.0 + 3.0 mm Drive: Hexalobular TORX® T25        

More information on : www.ejot.de

Applications :
Fastening timber laths to aluminium substructure ≤ 2 mm        

Properties :
A2 stainless steel Countersunk head with milling ribs        

Technical specifications :
Drilling capacity tI + tII: 2.0 mm Drive: Hexalobular TORX® T25        

More information on : www.ejot.de

Applications :
Fastening profiled steel and aluminium sheets and sandwich panels to 4-10 mm steel substructure Fastening aluminium profiled sheets to 4-12 mm aluminium substructures        

Properties :
A4 stainless steel with hardened steel drill point Stainless steel sealing washer Pre-assembled sealing washer        

Technical specifications :
Drilling capacity tI + tII: 2.0 + 10.0 mm Drive: Hexagon A/F8 Installation rotation speed: max. 1300 rpm        

More information on : www.ejot.de

Applications :
Fastening profiled steel sheets to 1.5 – 5 mm steel substructure Fastening profiled aluminium sheets and sandwich panels to 1.5-5 mm steel substructure        

Technical specifications :
Drilling capacity tI + tII: 2.0 + 4.0 mm  Drive: Hexagon A/F8 Installation rotation speed: max. 1300 rpm        

More information on : www.ejot.de

Applications :
To form floating and fixed points on substructures of rear ventilated facades Fastening pre-drilled stainless steel or aluminium wall brackets to aluminium support profiles For component assemblies from 3.1–5.0 mm (component I + component II)        

Technical specifications :
Drilling capacity: 2.0 m Drive: Hexagon AF8 Flange head: Ø 13 mm Material: A4 stainless steel Length non-threaded part: 5.0 mm        

More information on : www.ejot.de