Tiplovi za Termoizolaciju i kontaktne fasade

Applications :
Universal screw-in anchor for countersunk and surface fixed installation in concrete and masonry   For all substrates (A, B, C, D, E) For all insulation boards For countersunk and surface fixed installation For homogeneous surfaces and even rendering Up to 40% faster installation With European Technical Approval (ETA)      

Properties :
Approved for all building materials Countersunk installation - EJOT STR principle with ejotherm STR cap for homogeneous surfaces and even rendering - quick and easy without milling dust Up to 40% fastener installation Reduced thermal transmission (0.001 W/K) Surface fixed installation using ejotherm STR plug Short embedment depths, high loads for maximum safety and economic anchor usage Permanent contact pressure Premounted screw for quick installation 100% setting control: the countersunk installation of the washer indicates safe anchorage        

Technical specifications :
Anchor diameter: 8 mm Washer diameter: 60 mm Drill hole depth, countersunk installation h1 ≥: 50 mm (90 mm) Drill hole depth, surface fixed installation h2 ≥: 35 mm (75 mm) Anchorage depth hef≥: 25 mm (65 mm) Screw drive: TORX T30 Point thermal transmission χ  countersunk installation: 0,001 W/K surface fixed installation: 0,002 W/K Use categories acc. to ETA*: A, B, C, D, E German DIBt approval: Z-21.2-1769 European Technical Approval: ETA-04/0023 Values in parentheses: anchoring in aerated concrete (use category E) *Specification according to ÖNORM B 6124 for concrete, solid brick and vertical brick Characteristic loads: Building material class A: Normal weight concrete C 12/15 acc. to EN 206-1: 1.5 kN Normal weight concrete C 16/20 - C 50/60 acc. to EN 206-1: 1.5 kN Pre-cast concrete panel C16/20 - C50/60: 1.5 kN Building material class B: Clay bricks (Mz) acc. to DIN 105: 1.5 kN Solid lime sandstone (KS) acc. to DIN EN 106: 1.5 kN Solid masonry of lightweight concrete (V) acc. to DIN 18152: 0.6 kN Building material class C: Vertically perforated clay bricks (Hlz) acc. to 105: 1.2 kN Vertical coring reference bricks (Hlz) acc. to ÖNORM B 6124: 0.75 kN Sand-lime perforated (KSL) acc. to EN 106: 1.5 kN Lightweight concrete hollow blocks (HbL)acc. to DIN 18151: 0.6 kN Baustoffklasse D: Lightweight aggregate concrete (LAC): 0.9 kN Building material class E: Autoclaved aerated concrete P2 - P7: 0.75 kN For calculation of design loads the national safety factors have to be included (e.g. Germany: 3). Please observe the approval.        

More information on : www.ejot.de

Applications :
Fastening of rail-systems Screw-in anchor for rails For fixing holding and base rails Approved for all categories of building materials        

Properties :
Approved for all categories of building materials Shortest embedment depths, minimum drill hole depths Highest loads for maximum safety Economic anchor usage Premounted screw for quick installation To compensate facade tolerances use spacers EJOT AS        

Technical specifications :
Anchor diameter: 8 mm Collar diameter:16 mm Drill hole depth h1 >: 35 mm (75 mm) Embedment depth hef >: 25 mm (65 mm) Screw drive: TORX T30 Use categories acc. to ETA: A, B, C, D German DIBt approval: Z-21.2-1769 European Technical Approval: ETA-04/0023 Values in parentheses: anchoring in aerated concrete (use category E)        

More information on : www.ejot.de

Applications :
Brick slip system anchor for concrete and masonry For concrete, solid and perforated masonry Anchor tube with small countersunk head for unobtrusive installation in the joint        

Properties :
Approved for concrete, solid and perforated masonry (A, B, C, D) Anchor tube with small countersunk head for unobtrusive installation in the joint Torsion-proof anchor tube Universal expansion zone for safe anchoring High loads Anchor with increased bending moment Premounted screw for quick installation German DIBt approval: Z-21.2-589        

Technical specifications :
Anchor diameter: 8 mm Diameter of countersunk head: 12 mm Drill hole depth h1 ≥: 80 mm Embedment depth hef ≥:  70 mm Screw drive: TORX T30 German DIBt approval: Z-21.2-589 Characteristic loads: Building material class A: Normal weight concrete ≥ C 12/15 acc. to EN 206-1: 1.0 kN Pre-cast concrete Panel ≥ B15: 0.25 kN Building material class B: Clay bricks(≥ Mz 12) acc. to DIN 105: 0.4 kN Solid lime sandstone (≥ KS 12) acc. to DIN EN 106: 0.4 kN Solid masonry of lightweight concrete (V) acc. to DIN 18152: 0.2 kN Building material class C: Vertically perforated clay bricks (Hlz) acc. to DIN 105: * Vertical coring reference brick (Hlz) acc. to ÖNORM B 6124: 0.75 kN Sand-lime perforated bricks (≥ KSL 6) acc. to DIN EN 106: 0.25 kN Lightweight concrete hollow blocks (≥ HbL 2) acc. to DIN 18151: 0.15 kN Building material class D: Lightweight aggregate concrete acc. to TGL: 0.3 kN *According to approval to be determined throught pull-out testing at the building. The design loads given are in accordance with the German building code. National safety factors are already incorporated. Please observe the approval.          

More information on : www.ejot.de